Did you know?

Push the handle down onto the upper shaft housing (Fig. 8). Make sure the bolt hole faces to the right (Fig. 8). Safety Label Upper Shaft 2. Insert the bolt into the bolt hole and push it through (Fig. 8). Housing Tighten the bolt with a flat-head screwdriver, but do not tighten the bolt completely . Page 11: Oil And FuelTo remove the head from a Craftsman weed eater, one needs to follow some simple steps. Start by unplugging the spark plug wire to prevent any accidental starting of the engine. Then, using an adjustable wrench, turn the nut holding the head in place counterclockwise to loosen it. Once loose, pull on the head gently until it comes off.Trimmer Craftsman 358.799190 Operator's Manual. 5.5 amp 17" cutting path electric line trimmer (8 pages) Trimmer Craftsman 358.799230 Operator's Manual. 4.0 amo 13 inch.gutting path electric weedwacker (10 pages) Trimmer Craftsman 358.799461 Operator's Manual. 4.0 amp motor 13 inch cutting path/.065 in. line electric weedwacker (10 pages)

Jeff's Little Engine Service explains HOW TO Remove and Replace the Cutting Head on an ECHO SRM-2400 Weed Trimmer. Changing the BLADE on a ECHO Weed Wacker, ...To activate the auto line feed of a trimmer head, you must bump the spool off the stoppers and allow the spool to spin. To stop the auto-feeding, an internal spring repositions the spool to rest against the stoppers. If the stoppers or spring is damaged or missing, the head can feed out the line uncontrollably.Push the handle down onto the upper shaft housing (Fig. 8). Make sure the bolt hole faces to the right (Fig. 8). Safety Label Upper Shaft 2. Insert the bolt into the bolt hole and push it through (Fig. 8). Housing Tighten the bolt with a flat-head screwdriver, but do not tighten the bolt completely . Page 11: Oil And FuelPosition the gasket on the nipples of the engine mount and hold the carburetor in place. Install the filter housing and secure it with the 2 mounting screws. Using a torque wrench, tighten the screws to 25 in./lbs. of torque. If you don't have a torque wrench, tighten them reasonable tightly. 07.

Locate the exit holes on the outside of the spool. Wind the lines onto the spool, leaving about 12 inches of the lines unwound. Push the ends of the lines through the exit holes, one line per hole, and slide the spool back into the cover. Make sure the lines can move freely. Snap the cover back onto the cutting head of the weed eater.Step by Step Instruction to reload string –. Check if you need .8″ or .6″ line. Cut the new line – 10 feet for .8″ line and 15 feet for .8″ line. Rotate the exterior spool so the arrow meets the interior arrow. Feed the line into the holes, leaving about 4″ as cutting line. ….

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. How to string a craftsman weed eater with two holes. Possible cause: Not clear how to string a craftsman weed eater with two holes.

Pull the starter cord quickly about eight times. Wipe any debris, oil and excess fuel off the spark plug with a shop towel. Insert the spark plug and turn it clockwise until tight with an adjustable wrench. Replace the spark plug wire on the top of the spark plug. Hold in the throttle trigger and pull the starter cord to start the Weed Eater.how to replace the line on a craftsman weed eater. Easily replace the string line on a string trimmer. Craftsman weed wacker line replacement made easy.#weed...

A 3 minute run down on the easiest way to replace your weed eater string. If you're having trouble with your weed eater and need to replace the string, this ...The four-cycle Craftsman propane model emitted the low rumble of a Harley-Davidson pulling up to a stoplight, and the oil/gas Troy-Bilt had the familiar string trimmer whine, like a 30-pound ...About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy & Safety How YouTube works Test new features NFL Sunday Ticket Press Copyright ...

greenville county sc inmate search Trimmer CRAFTSMAN WEEDWACKER 358.791030 Operator's Manual. 25cc/1.5 cu.in. 2-cycle gasoline weedwacker (40 pages) Trimmer CRAFTSMAN WEEDWACKER 358.791041 Operator's Manual. 32cc/1.9 cu.in. 2-cycle 17 inch cutting path / 0.080 inch line gasoline weedwacker (21 pages) Trimmer CRAFTSMAN WEEDWACKER 358.791071 Operator's Manual.This will cause the string to go into the head and be looped around the inside of the device. 6. Rescrew the Head. Take the head of the weed eater and rotate it counterclockwise until the string is all the way through. There should be just enough string out of the sides shorter than the shield guard width. nyu student insuranceicd 10 ruq abd pain In this video you will learn how to change fuel lines on a weed eater, blower, hedge trimmer, chainsaw and other equipment powered by two cycle/two stroke en... provo weather hourly Step 2. Cut off approximately 10 feet of weed eater string. Insert each end of string into the openings around the center of the unit that hold it. Pull the string where it fits tight around the inside section of the holding unit. Leave one side of the string approximately six inches longer than the other side of the string.String Trimmer carburetor tear down, clean, and reassemble for bogging weed wacker.My Amazon Store:https://www.amazon.com/shop/sevenfortyoneMy Wife's Art:htt... latitude at mallard creek reviewsathens al power outage todayjcpenney kiosk sign in associates To activate the auto line feed of a trimmer head, you must bump the spool off the stoppers and allow the spool to spin. To stop the auto-feeding, an internal spring repositions the spool to rest against the stoppers. If the stoppers or spring is damaged or missing, the head can feed out the line uncontrollably.Step 2. Cut off approximately 10 feet of weed eater string. Insert each end of string into the openings around the center of the unit that hold it. Pull the string where it fits tight around the inside section of the holding unit. Leave one side of the string approximately six inches longer than the other side of the string. elkhart county accidents today Solution. The 3 fuel lines should be connected as follows: The (clear) main fuel line with the filter (filter inside the fuel tank) goes to the bottom of the carburetor (or the elbow shaped nipple). The (clear) fuel intake line runs from the top of the carburetor (straight nipple) and goes to the short post on the back of the primer bulb. five nights at chuck e cheese rebootedemt saddle bendpsalms 91 nlt version Unfortunately, ii holes are a little more complicated to re-spool than i. Every bit long equally yous accept the right tools and follow these steps, y'all can hands string the dual-sided weed eater spool. (Read Straight Vs Curved Trimmer) ane. Turn off your weed eater. Unplug from the mains if you accept an electric corded weed eater.